Home > technology > 180 Grit Aluminum Oxide Manufacturers UK

180 Grit Aluminum Oxide Manufacturers UK

Electric furnace preparation is to clean up and repair the used resistance furnace and prepare to use it again. The 180 grit aluminum oxide blasting media main operations include: cleaning up the spent or roasted material at the bottom of the furnace, trimming the electrodes, cleaning, repairing, installing the furnace wall, and inspecting and removing other defects of the aluminum oxide blast media 60 grit furnace body.


180 Grit Aluminum Oxide Manufacturers UK MOQ: 1 Ton! 19 Years Experience 180 Grit Aluminum Oxide Manufacturer, 35,000m² Workshop Area, Free Samples, Fast Delivery!


If you want to buy 180 grit aluminum oxide, please click our products: Brown Fused Aluminum Oxide or White Aluminium Oxide or Black Aluminum Oxide or Pink Aluminum Oxide for more information!


Trimming the electrode refers to clearing the oxy silicon carbide, 220 grit aluminum oxide, etc. that are stuck on the electrode, so that the electrode end is exposed to a fresh surface; repairing the oxidation gap of the electrode and the carbonaceous masonry around the electrode, filling the graphite paste and smoothing it. It's like a set of rectangular boxes without a cover. The refining 70 grit aluminum oxide blast media adopts constant power transmission. 


Generally speaking, the charging of a furnace is to fill the brown fused alumina furnace with reaction materials, insulation materials and furnace cores according to the type, location and size of the furnace materials specified in the process. In order to ensure that the location and size of the charge at each part meet the requirements and are not mixed with each other, a furnace partition is also used when installing the 240 grit aluminum oxide furnace, also known as a partition box.


When the bottom material and the 80 grit aluminum oxide lower reaction material are installed, install them in the resistance furnace one by one. Put different charge and core charge into different spaces. After filling and filling, pull out the partition box and reload the upper charge. The use of the partition box can ensure that the charge is not mixed in each part. In the core material, power transmission and smelting, do not mix 46 grit aluminum oxide and scrap materials.


Note that the brown aluminum oxide furnace core size and density are uniform, so that the furnace core resistance is uniform. The charge below the core should be compacted to prevent the core from sinking. Moving furnace and resistance furnace with transformer moving. After the smelting of one furnace is completed, another resistance furnace is needed for smelting, and the 1200 grit aluminum oxide power needs to be switched. The key part of furnace installation is the furnace core.


Both ends of the fine grit aluminum oxide furnace core are made into a horn shape and connected to the electrode, and tamped to reduce the contact resistance with the electrode. The contents of refining operations include power switching, carbon monoxide ignition, abnormal phenomenon treatment, and power failure. The soil method connects the electric furnace flexible wire and the 120 grit aluminum oxide harbor freight transformer bus with copper plates and bolts.


The first two methods are easy to operate and have short switching time. The method is simple and low in cost, but the brown aluminium oxide switching time is slightly longer. However, it is not required to reach the required power immediately after power is supplied. There are three methods for switching power: using a cam power connection mechanism; 220 grit aluminum oxide blast media using a screw power connection mechanism; earth connection. It must be manually ignited.


Because in this case, the furnace resistance in the initial stage is smaller and the 180 grit aluminum oxide furnace resistance in the later stage is smaller, which will cause the current in the later stage to be too high and exceed the rated power. It is more appropriate to reach the rated power after 1h of power transmission. After 100 grit aluminum oxide media power transmission and refining, carbon monoxide gas is generated by the reaction in the furnace, and it continuously escapes.


At the beginning, the 150 grit aluminum oxide monoxide concentration was too low to ignite. Usually, it can be ignited after 10 ~ 30min, sometimes it takes several times to ignite. The specific time depends on the rate of increase of furnace power and the thickness of the charge. When igniting, an open flame is used to ignite one place, and the whole 80 grit aluminum oxide blasting media furnace surface will catch fire, and at the same time, it will make a popping sound.


white aluminium oxide
Contact Us
  • Contact:Terry
  • Tel:0086-15515998755
  • Wechat:Wilson15515998755
  • Whatsapp:0086-15515998755
  • Email:terry@wilsonabrasive.com
Follow Us

Wilson Abrasive CO.,LTD Copyright © 2001-2020 All Rights Reserved. sitemap

Brown Fused Alumina And White Fused Alumina MOQ: 1 Ton! 19 Years Manufacturing Exprience, 35,000m² Workshop Area, Factory Price, Free Samples, Fast Delivery!

no cache
Processed in 1.294152 Second.