70 Grit Aluminum Oxide

After hearing the start-up warning signal, the operator stood at a safe place two meters away from the ore washing machine and waited for the start-up(70 grit aluminum oxide). After the equipment is started, adjust the flushing water until it is appropriate according to the mud content of mixed bauxite(corundum sand). Whether the meshing of the shaft device is normal, if any abnormality is found, it should be reported and dealt with in time.

70 Grit Aluminum Oxide MOQ: 1 Ton! 19 Years Experience 70 Grit Aluminum Oxide Manufacturer, 35,000m² Workshop Area, Free Samples, Fast Delivery!

If you want to buy 70 grit aluminum oxide, please click our products: Brown Fused Alumina or White Fused Alumina or Black Aluminum Oxide or Pink Corundum for more information!

With the continuous and healthy development of China's economy, the release of white corundum demand growth, and the rapid development of its market, it is increasingly showing unprecedented vitality(70 grit aluminum oxide). In the shoe industry, wear-resistant and non-slip materials added to the outside of the heel of the shoe sole, and used for fire and heat insulation of medium and low temperature parts(aluminium oxide blasting). 

Check the temperature and sound of motor and reducer bearing every half an hour, and report and deal with abnormalities in time(aluminum oxide abrasive media). In case of any abnormality, report and deal with it in time. During daily equipment operation, the temperature of motor and bearing shall be measured manually every 30min(70 grit aluminum oxide). When measuring the temperature manually, the back of hand shall be used for contact test. 

During the operation of the equipment, pay attention to the slag removal of the tail overflow tank, pay attention to whether the flushing water volume(green silicon carbide), water pressure and water quality meet the ore washing requirements, carefully lubricate the copper sleeve, large and small gears and bearings, and observe whether the blades are loose or fall off(70 grit aluminum oxide). Observe the operation of the conveyor chain plate(aluminum oxide abrasive blasting grit).

If there is lack of oil, add oil immediately(70 grit aluminum oxide). Check whether there is abnormal sound, vibration (runout) and temperature rise in each operating part, motor, reducer, copper sleeve, large and small gears and the bearing seat of the second shaft of the coupling(alumina sand). There will be capillary voids in the calcination process of brown corundum abrasive, resulting in a certain hydrophilicity of brown corundum abrasive. 

It is normal if it is not hot within 4S, otherwise it is abnormal, and oil shall be injected if necessary(70 grit aluminum oxide). When receiving the shutdown signal from the main control room, first turn the speed regulating meter counterclockwise to the "zero" position, then turn off the power switch, and then press the "stop" button to stop the machine(240 grit aluminum oxide blast media). Observe the meshing and operation of motor, reducer and gear pair. 

After the equipment is started, daily check the water pressure of the sealing water of the underwater bearing shaft, observe whether the spiral shaft is blocked and whether the gear pair has clear teeth, and adjust the flushing water until it is appropriate according to the mud content of mud bearing bauxite(black silicon carbide). Always pay attention to uprooting tree roots and other sundries on the overflow network(70 grit aluminum oxide). 

During operation, pay attention to monitor whether the operation sound of each part is normal, often check whether the blades and anchor bolts are fastened(aluminum oxide 80 90 grit), stop the machine immediately if any abnormality is found, and hang the sign board of "equipment maintenance, no closing"(70 grit aluminum oxide). The material under the cylinder screen should be distributed evenly to the two tank washing machines. 

When the stop signal is heard, wait for the upper process to stop, and the ore in the cylinder is basically empty and then the machine is stopped manually(aluminium oxide sandblasting grit). If the transported materials are obviously too few or empty, confirm whether there is ore in the ore bin, and urge the crusher driver to pick up the ore in time(70 grit aluminum oxide); In case of insufficient ore supply, report to the team leader or dispatching room in time. 

Due to the small proportion of slag, small slag particles are suspended in the air, resulting in environmental pollution(70 grit aluminum oxide). Our company is a professional manufacturer of abrasive silicon carbide and brown corundum, with good reputation, good products and favorable prices(garnet sand). The production and sales volume of non-metallic bonded abrasives will comprehensively exceed that of metal bonded abrasives. 

There are many kinds of abrasives, but the most commonly used are white corundum powder, brown corundum powder and black corundum powder(70 grit aluminum oxide). It has good durability, better impact resistance, and has a certain effect on anti-static(aluminium oxide sand). For example, fine-grained additives for wear-resistant and fire-resistant coatings, because of low cost, resin abrasive tools made of composite abrasives have a very high cost performance.

In case of deviation, adjust it first(steel grid); If it is unable to adjust and the deviation is serious, as well as the chain plate is desoldered and deformed, report to the dispatcher and stop the machine for treatment(70 grit aluminum oxide). If there is a dead angle in the flushing water jet, which causes mud accumulation, or the funnel liner is deformed, shifted or falls off, report to the dispatching room and deal with it when the machine is shut down. 

If the anchor bolts of bearing seat are loose or missing, fasten or supplement them in time(46 grit aluminum oxide); In case of abnormal sound and temperature rise, report to the supervisor, and the special inspector shall determine the handling opinions on site(70 grit aluminum oxide). The inspection and operation lines are: tank washing machine → drum washing machine, a heavy-duty plate feeder; one equipment spot inspection is required every 120 minutes. 

During the operation of the equipment, check the integrity of the sieve bar, water retaining ring(glass bead blasting media suppliers), and rubber lining, whether the flushing water volume, water pressure and water quality meet the washing requirements, whether the supporting wheels, retaining wheels, and rolling rings have shifted, large and small gears, and couplings(70 grit aluminum oxide). Actively observe the material transportation on the heavy plate chain plate. 

If it cannot scrape mud, adjust it and report to the dispatching room if it is serious(aluminum oxide grit blasting). Observe whether the adjustment of the speed controller is flexible and reliable. If the speed adjustment fails, report to the dispatching room for processing(70 grit aluminum oxide). The inspection and operation lines are(aluminum oxide blasting grit): tank washing machine, cylinder washing machine, one heavy plate feeder; equipment spot inspection is required every 120 minutes Work. 

Participate in fire safety education and training, be proficient in the use of fire-fighting facilities and equipment, be familiar with fire hazards and fire-prevention measures at this position, and improve sales and safety business skills and the ability to deal with accidents(aluminum oxide abrasive powder). During the operation, one inspection should be carried out every 60 minutes(70 grit aluminum oxide). Observe the meshing and operation of the motor, reducer, and gear pair.

Observe whether the mud scraping device is normal for mud scraping(aluminium oxide blast media). After hearing the start-up warning signal bell, the operator successively opens the underwater tile shaft sealing water valve and flushing water valve, and stands at a safe place one arm away from the ore washing machine switch box to wait for start-up(alumina grit). In the daily operation process, one inspection should be carried out every 60 minutes(70 grit aluminum oxide). 

Check the lubrication of all transmission parts, and there shall be no lack of oil(70 grit aluminum oxide). The inspection and operation lines are: tank washing machine→same drum washing machine→heavy plate feeder; one equipment spot inspection is required every 120 minutes Work(white aluminum oxide 80 grit). Observe the operation of the cylindrical motor, reducer and coupling, and report to the dispatching room when there is an abnormal sound (loose bolts).

The spot inspector confirms the handling opinion on the spot(100 grit aluminum oxide). With the improvement of product quality, the scope of application is still expanding(70 grit aluminum oxide). If the anchor bolts of the bearing seat are loose or missing, they should be tightened or supplemented in time; if there is abnormal sound and temperature rise, report to the dispatching room, and the spot inspector will determine the treatment opinion on the spot.

If the material is unevenly distributed, adjust the cylinder flushing water valve to adjust the water volume for treatment(70 grit aluminum oxide); if the material is still severely uneven after adjustment, report to the dispatching room, and Technicians and spot inspectors determine the treatment opinions on site(aluminium oxide abrasive grit). Observe the material flow in the barrel of the drum washing machine, and the inlet and outlet of the material should be unblocked.

During the operation, one inspection should be carried out every 60 minutes(120 grit aluminum oxide). Clean up the tree roots, grass roots and other debris in the overflow trough of the trough washing machine in time; reduce the feeding amount or flushing water when there is a rough run to ensure the smooth flow of the trough washing and overflow(70 grit aluminum oxide). Take good care of and maintain the fire-fighting facilities and equipment at this post.