Home > application > Aluminum Oxide 1000 Grit Wholesale Suppliers USA

Aluminum Oxide 1000 Grit Wholesale Suppliers USA

Use 17% rosin soap, 12% bone glue (gelatin), and 71% water to prepare an emulsified liquid(black silicon carbide powder). Foam method light-weight bricks formed by grouting, due to large deformation and large shrinkage after firing, products must be cut and ground. Injection molding, the prepared foam liquid is poured into a low-level horizontal cylindrical mixer, at the same time, the stirred mud is added while stirring(carborundum powder), and then mixed and stirred for about 10 minutes to make a foam slurry.


Aluminum Oxide 1000 Grit Wholesale USA MOQ: 1 Ton! 19 Years Experience Aluminum Oxide Grit Wholesale Supplier, 35,000m² Workshop Area, Free Samples, Fast Delivery!


If you want to buy aluminum oxide 1000 grit, please click our products: Brown Fused Aluminum Oxide or White Aluminium Oxide for more information!


The amount added is about 4% of the volume of the foaming machine(green silicon carbide powder). It can be made into a foamy liquid with a bulk density of 0.04~0.06g/em by bubbling for about 15min. Stir the mud in a horizontal mud bucket, the stirring time is 15min, keep it synchronized with the foaming machine. The bubbler and beater installed in the high position should be started synchronously(silicon carbide grit suppliers). Products made by pressurized vibration also use wooden molds or metal molds.(aluminum oxide 1000 grit wholesale suppliers usa)


Therefore, the grouting mold design should take into account the sintering shrinkage and processing allowance of the product(carborundum abrasives). The general ruler rate is 40% and 50%, and it is poured with a wooden mold or a metal mold. Drying, when drying in the drying room of the intermittent drying system, it is necessary to grouting on the dry kang. When the grouting in a drying room is completed, the door is sealed and heated to dry(carborundum grit suppliers). Then raise the temperature and dry at 100-120℃ for 3-4 days.


The dry and dense population temperature is 50~60℃, and the outlet temperature is 100-120℃(white fused alumina). Then separately grouting, while stirring with a special tool (small target), to exclude the atmospheric pool of mud injected into the mold, the uppermost part is flattened with a flat plate. Grouting, when drying in the tunnel drying kiln, must be grouting on the drying truck(aluminum oxide sandblasting). First dry at 50~60℃ for 24h to make the brick shape and release the mold.


(aluminum oxide 1000 grit wholesale suppliers usa)When grouting, grouting is carried out from the lower layer to the upper layer in sequence, and each time it is filled with a vehicle, it is immediately sent to the tunnel drying kiln(white aluminum oxide). For kiln installation, due to the light brick produced by the foam method, the volume density is small and the compressive strength is low(silicon carbide 180 grit). Firing, the firing temperature of the product is 1500-1600℃, heat preservation is 4-6h, and the total firing time is 50-60h.


Use the method of controlling the density of foam mud to produce alumina foam lightweight bricks with different volume densities(white corundum). It is necessary to use the shelf method to install the kiln for firing. The products are fired in corrugated bricks or gas-fired high-temperature kilns with corundum bricks or electric fusion directly combined with magnesium bricks. The residual moisture of the green body after drying should be less than 2%(carborundum grit). The residual moisture of the brick is less than 5%.


The ratio (volume ratio) of mud to foam liquid is required to be controlled at 1:0.75-1.0, and the density of mud can fluctuate between 0.54~1.05g/cm(arc fused alumina). Packing height: the product density of the bulk density is 0.8-1.0g/em, it can be installed 4 heights (about 600mm); the bulk density is 0.6-0.8g/em, it can be installed 3 heights (about 450mm); If the volume density is 0.4~0.6g/cm, 1-2 heights (200-300mm) can be installed on the side(silicon carbide abrasive grit). Put it in a foaming machine and stir it for foaming.(aluminum oxide 1000 grit wholesale suppliers usa)


white aluminium oxide
Contact Us
  • Contact:Terry
  • Tel:0086-15515998755
  • Wechat:Wilson15515998755
  • Whatsapp:0086-15515998755
  • Email:terry@wilsonabrasive.com
Follow Us

Wilson Abrasive CO.,LTD Copyright © 2001-2020 All Rights Reserved. sitemap

Brown Fused Alumina And White Fused Alumina MOQ: 1 Ton! 19 Years Manufacturing Exprience, 35,000m² Workshop Area, Factory Price, Free Samples, Fast Delivery!

no cache
Processed in 0.994963 Second.