Home > wholesale > Aluminum Oxide Blast Media Manufacturers Ukraine

Aluminum Oxide Blast Media Manufacturers Ukraine

It is necessary to strictly prevent materials that cannot be broken from entering the drunk cavity, such as bucket teeth, drill bits and track shoes(aluminum oxide blast media manufacturers ukraine). When the impact crusher is running, the staff cannot stand within the range of the inertial force line of action, and the installation of the electrical switch should avoid this position(aluminium oxide sandblasting grit). 


Aluminum Oxide Blast Media Manufacturers Ukraine MOQ: 1 Ton! 19 Years Experience Aluminum Oxide Blast Media Manufacturer, 35,000m² Workshop Area, Free Samples, Fast Delivery!


If you want to buy aluminum oxide blast media, please click our products: Brown Fused Alumina or White Fused Alumina or Black Aluminum Oxide or Pink Corundum for more information!


The feeding should be stopped before the machine is shut down, and the machine should be shut down after the material on the screen surface is drained(aluminum oxide sandblasting media). Check whether the ore feeding is uniform. Regular maintenance (monthly). During the operation of the equipment, if the product size is found to be too large, the machine should be shut down to adjust the clearance of the discharge port(aluminum oxide blast media manufacturers ukraine). 


Feeding must be stopped before stopping operation(alumina grit), and the motor can be stopped after all the materials in the crushing cavity are exhausted(aluminum oxide blast media manufacturers ukraine). When the crusher is running, the operator should pay attention to whether the blind chamber and the discharge port are blocked, and observe whether the tension of the tension spring is appropriate(silicon carbide powder). In case of abnormal conditions, it shall be shut down for treatment. 


Tighten the screws and connecting parts of the particle crusher, and check the lubrication(aluminium oxide blasting). Feeding must be uniform during operation, which is conducive to increasing output(aluminum oxide blast media manufacturers ukraine). When the impact crusher is running, it is strictly forbidden to open the inspection door to observe the situation inside the machine, and it is strictly forbidden to carry out any adjustment, cleaning, maintenance and other work to avoid danger.


The shutdown shall be supervised by a specially assigned person or powered off at the power switch and hung with warning signs to prevent others from starting the equipment(aluminum oxide abrasive powder). When the impact crusher is running, you can't stand within the range of the inertial force line of action, and the installation of the electrical switch should avoid this position(aluminum oxide blast media manufacturers ukraine). Check whether all parts of the machine are working properly(aluminum oxide blasting grit).


When the impact crusher is running, the vibration, temperature and abnormal sound should be checked routinely in accordance with the inspection requirements(aluminum oxide blast media manufacturers ukraine). Apply for shutdown inspection, eliminate the fault in time, and then continue to start operation(silicon carbide grit). During the operation of the equipment, it is not allowed to touch the vibrating part of the screen box or close to the rotating part of the drive belt. 


Check the degree of wear of easily worn parts, and pay attention to replacing worn parts at any time(alumina sand). If the bearing oil temperature rises, stop the machine immediately to check the cause and eliminate it(aluminum oxide blast media manufacturers ukraine). When a person enters the warehouse, the rotor should be blocked with a wooden sleeper before entering(corundum sand). When the impact crusher is stopped for maintenance, the working power supply should be cut off. 


Check whether the lubricating condition of each bearing is normal and whether there is oil shortage(aluminum oxide blast media manufacturers ukraine). When the equipment is started, it should run with no load, observe whether the screw shaft is jammed, whether the gear pair has clear teeth, and confirm that there is no abnormality before feeding(white aluminum oxide 80 grit). The staff should stop feeding before stopping the machine and empty the material in the tank before stopping the machine.


Add and change oil for each part of the equipment according to the lubrication standard, and record it on the equipment refueling record book(aluminum oxide blast media manufacturers ukraine). The brand of lubricating oil (grease) shall not be changed at will, and the lubricating oil (grease) shall be clean and free of sundries(garnet blasting media). When abnormal sound is found or the bearing temperature is higher than 75℃, the operator should immediately report to the shift supervisor. 


When the machine is running, it is strictly prohibited to overload the machine(aluminum oxide blast media manufacturers ukraine). Tighten the loose bolts, make up the defects, and replace the seriously worn bolts. If the equipment paint falls off and rusts, it shall be derusted and painted(aluminum oxide abrasive media). When the particle size of the impact crusher is too large, the machine should be shut down to check the wear of the hammer to prevent the rotor from being worn out.  


After the on-site supervisor's permission is obtained, the on-site power supply must be disconnected, and the "equipment maintenance, no closing" warning sign can be displayed before the equipment failure can be handled(aluminum oxide grit blasting). Before handling equipment failures, the on-duty supervisor must be notified(aluminum oxide blast media manufacturers ukraine). When replacing the screen, dealing with the screen blockage or removing obstacles, it must be listed and shut down.


The equipment inspection and maintenance shall be carried out under the shutdown state(alumina abrasive). When the equipment is started, it shall run at no load as far as possible without special circumstances(aluminum oxide blast media manufacturers ukraine). After the screen runs stably and confirms that the equipment is normal, it can be fed, and strive to achieve uniform feeding. Always pay attention to the discharge of jaw crusher(steel shot abrasive). In case of blockage, dredge it in time. 


Special tools must be used for the lubrication of gear pair. Before the equipment is shut down, the feeding shall be stopped first, and the equipment can be shut down only after the materials on the screen surface are discharged(aluminum oxide blast media manufacturers ukraine). The air hole of vibrator shall be kept unblocked frequently(46 grit aluminum oxide). Turn on the shift, do a good job of site hygiene, carefully fill in the shift record, and handover with the successor on the post. 


During operation, the bearing temperature of motor and vibration exciter shall be checked frequently, and the screen shall be checked for abnormal noise(aluminum oxide abrasive blasting grit). Observe the vibration of the sieve and whether its amplitude is within the specified range(aluminum oxide blast media manufacturers ukraine). Clean the residual oil in the open gear pair and trunnion bearing bush, and recycle it to a special oil barrel for storage(glass bead abrasive). Pay attention to avoid clamping the tools when refueling. 


It is strictly forbidden to stop the equipment at will during operation(aluminum oxide blast media manufacturers ukraine). In case of emergency, emergency shutdown or manual shutdown in the main control room shall be adopted. Refuel all parts of the equipment according to the lubrication standard table without oil shortage, and record it in the equipment refueling record book(aluminum oxide 80 90 grit). During equipment operation, all parts shall be inspected every 2h, i.e. patrol inspection.


Attention must be paid to the daily routine inspection of equipment according to the daily routine inspection standards and recorded in the daily routine inspection record book(aluminum oxide blast media manufacturers ukraine). Check whether the bolts at each part are loose, tighten the loose bolts and make up the defects. The residual oil shall be recovered in time and stored in special oil drums(aluminium oxide sand). The environment around the equipment shall be cleaned every shift.


Clean the equipment frequently to keep it free of dust and oil(aluminium oxide blasting media). When cleaning the environment with water pipes, it is not allowed to drink wine to the motor and operation box. Regularly check whether the bearing seal is good, fill the lubricating grease in the bearing seat once a month, and clean and change the oil every three months(aluminum oxide blast media manufacturers ukraine). If the equipment paint falls off and rusts, it shall be derusted and painted(240 grit aluminum oxide blast media). 


white aluminium oxide
Contact Us
  • Contact:Terry
  • Tel:0086-15515998755
  • Wechat:Wilson15515998755
  • Whatsapp:0086-15515998755
  • Email:terry@wilsonabrasive.com
Follow Us

Wilson Abrasive CO., LTD Copyright © 2024 All Rights Reserved.

Brown Fused Alumina And White Fused Alumina MOQ: 1 Ton! 19 Years Manufacturing Experience, 35,000m² Workshop Area, Factory Price, Free Samples, Fast Delivery!