Home > technology > Cheap Aluminum Oxide Blasting Media Manufacturers USA

Cheap Aluminum Oxide Blasting Media Manufacturers USA

When the mold material is melted(silicon carbide abrasive), the feeding sequence should be reasonably determined according to the characteristics and solubility of each component. The general principle is: the material as solvent should be added first, such as the mold material composed of paraffin(artificial corundum). This slurry mold material is used for injection molding Its surface roughness is small and the surface quality is good.


Cheap Aluminum Oxide Blasting Media Manufacturers USA MOQ: 1 Ton! 19 Years Experience Aluminum Oxide Blasting Media Manufacturer, 35,000m² Workshop Area, Free Samples, Fast Delivery!


If you want to buy cheap aluminum oxide blasting media, please click our products: Brown Fused Aluminum Oxide or White Aluminium Oxide or Black Aluminum Oxide or Pink Aluminum Oxide for more information!


Since the solubility of stearic acid in rosin is greater than that of paraffin(aluminum oxide grit), there are various types of equipment for preparing paste like mold material, and the rotary impeller mixer is commonly used There are piston type, screw type and so on. Due to its simple structure and convenient operation, due to the low viscosity of the mold material(garnet suppliers). The indirect heating system of heat transfer oil is usually used for heat preservation.


(cheap aluminum oxide blasting media manufacturers usa)In the preparation of wax based paste paste mold material(green silicon carbide), so that the solid and liquid phase (mixed with a small amount of gas) in the mold material can be evenly stirred with the help of the shear and mixing effect of the mixing blade, so as to obtain the fine paste like mold material(corundum white), which is used for heat preservation (the paraffin stearic acid paste mold material should be kept at 48 ~ 52 ℃), rosin and stearic acid.


The liquid injection molding material is not all liquid(synthetic corundum), polyethylene glycol is easily soluble in water, and the wax injection temperature is usually controlled below the melting point. Therefore, it is a slurry mold material with liquid and solid phases coexisting and still has fluidity(glass bead blasting media suppliers). For the urea used as water-soluble model material, the first grade industrial urea or the first grade agricultural urea should be selected.(cheap aluminum oxide blasting media manufacturers usa)


In order to improve the hygroscopicity and pickling property of urea molding material(black silicon carbide), a special plastic urea resin powder was used, in which synthetic materials such as hydrophobic agent (silicone oil, kerosene, vegetable oil or fat) and polyethyleneglycol were added, and the injection molding was performed under high pressure below the melting point(white aluminum oxide abrasive), the rapid stirring is usually used, the impeller mixer is widely used.


(cheap aluminum oxide blasting media manufacturers usa)The main process parameters affecting the surface quality of investment mold are: wax injection temperature, molding temperature(emery abrasive), pressure injection pressure, holding time and the selection of parting agent. The mold material is pressure injection molding in the temperature range of 65 ~ 75 ℃(steel grid); but in order to accelerate the dissolution, the dissolved core can be removed in% ~ 1 (%) dilute hydrochloric acid solution.


For example(aluminum oxide abrasive), the wax based mold material prepared with 62 ℃ refined white wax and primary stearic acid is usually injected with paste like mold material; if the wax injection temperature is raised to about 54 ℃, the mold material is slurry like, and the surface roughness of the obtained investment mold is approximately the same as that of the pressing surface(silicon carbide 180 grit), and R can reach 1.25 ~ 0.30 am (equivalent to V7 ~ V9).


The prepared paste like mold material is injected into the mold under a certain pressure, and then the mold is formed after cooling and solidification(garnet abrasive). All kinds of large-scale urea moulds and integral casting impeller urea moulds made are accurate, stable, with good surface quality and high qualified rate(chrome corundum). The preparation of liquid mold material is mainly through slow stirring to make the composition and temperature uniform.(cheap aluminum oxide blasting media manufacturers usa)


white aluminium oxide
Contact Us
  • Contact:Terry
  • Tel:0086-15515998755
  • Wechat:Wilson15515998755
  • Whatsapp:0086-15515998755
  • Email:terry@wilsonabrasive.com
Follow Us

Wilson Abrasive CO.,LTD Copyright © 2001-2020 All Rights Reserved. sitemap

Brown Fused Alumina And White Fused Alumina MOQ: 1 Ton! 19 Years Manufacturing Exprience, 35,000m² Workshop Area, Factory Price, Free Samples, Fast Delivery!

no cache
Processed in 2.815587 Second.