Home > technology > Cheap White Fused Alumina For Refractory Japan

Cheap White Fused Alumina For Refractory Japan

With the increase of the white aluminum oxide mud structure constant, the diffusion layer is obviously thickened, and the number of free dispersion media is correspondingly reduced. The female model comes from the male model. After the gypsum slurry is injected into the frame, wait for about half an hour, let it heat and solidify, then low density white alumina remove the frame and take out the male mold, that is to say, the female mold for pouring molding is obtained.


Cheap White Fused Alumina For Refractory Japan MOQ: 1 Ton! 19 Years Experience White Fused Alumina Manufacturer, 35,000m² Workshop Area, Free Samples, Fast Delivery!


If you want to buy cheap white fused alumina for refractory, please click our products: White Aluminium Oxide for more information!


And so on, until the brown aluminum oxide 250 grit combination is completed. Under these conditions, the fewer the blocks, the better. In addition, it is confirmed that the interaction between particles is strengthened. However, different from the previous P increase process, in the same range, the formation speed of the green body and the thickness of the formation layer are slowed down, so the density of the green body poured with this slurry is larger (2.5-2.7g / cm2), but smaller (2.65-2.80g / cm2) than that without brown fused aluminum oxide suppliers.


Put the male mold in a special frame, brush a layer of release agent on the white corundum surface of the male mold, and then according to the wall thickness of the female mold, the ratio of gypsum to water is 1:0.75 ~ 1, static for 1 ~ 2min, after the water is completely soaked with gypsum powder, quickly mix it for 2min to make it fully and evenly mixed, and then sift to remove impurities, and then slowly pour it into the frame Fill again, silicon carbide companies and then vibrate slightly to discharge bubbles.


In the design of the combined model, it is necessary to consider that it is convenient for grouting and mold unloading, brown fused alumina price and does not hinder the shrinkage of the injection parts in the mold cavity. When drying, the combination block shall be well matched, clamped with clamps, pweigh a certain amount of hemihydrate gypsum powder and gently pour it into the clean water, laced flat and stable, and the brown fused alumina oxide single block shall not be taken apart for drying to prevent deformation.


After the black corundum mold is made, it should be dried. When making the combined mold of Haff, first draw the boundary line on the male mold, apply the mold release agent, and then inject the first face, and then carve the triangle or semicircle groove on this face, and apply the mold release agent, and inject the second face. The two faces are combined into the Haff mold. The drying degree of the model depends on the shape, green carborundum size and grouting method of the product.


The first mock exam is a complex white fused alumina product, and no single model can be used. Generally, the moisture content of gypsum mold is 5% ~ 12%, the shape is complex, the model of small and thin products is higher than the upper limit, the model of large and thick products is lower than the lower limit. The forming speed of the injection part is related to the porosity of the gypsum mold, wholesale brown fused alumina and the porosity is related to the mixing ratio of gypsum powder and water.


The pink corundum process of gypsum injection molding is a physical process, because the gypsum mold has a high water absorption rate. Under the influence of the capillary force and external force (pressure, centrifugal force, vacuum) of the gypsum mold, the water of the mud moves to the inside of the gypsum mold, and the solid components of the mud are adsorbed on the inner wall of the gypsum mold to form the injection parts, silicon carbide price and the drying temperature is about 65 ℃.


white aluminium oxide
Contact Us
  • Contact:Terry
  • Tel:0086-15515998755
  • Wechat:Wilson15515998755
  • Whatsapp:0086-15515998755
  • Email:terry@wilsonabrasive.com
Follow Us

Wilson Abrasive CO.,LTD Copyright © 2001-2020 All Rights Reserved. sitemap

Brown Fused Alumina And White Fused Alumina MOQ: 1 Ton! 19 Years Manufacturing Exprience, 35,000m² Workshop Area, Factory Price, Free Samples, Fast Delivery!

no cache
Processed in 1.602202 Second.